INFLUENCE OF COEFFICIENT OF FRICTION ON THE PERFORMANCE OF PARALLEL GEARS

Authors

  • M. Aroudj Mechanical Engineerind Department,University 20Aout 1955 Skikda
  • F. Inel Mechanical Engineerind Department,Automatic Laboratory, University 20Aout 1955 Skikda

DOI:

https://doi.org/10.4314/jfas.v11i3.6

Keywords:

gear, performance, coefficient of friction, rotation speed, comparison

Abstract

Gears performance is a very essential value that concluded the success of our system so researchers have worked hard to find mathematical relationships to calculate performance. Between these relationships we have the J.F. Debongnie method and the f.VILLE and VELEX method.

In this work the yield of the parallel gears was calculated with the change of the modulus and the number of teeth using the J.F. Debongnie method and comparing them with the f.VILLE and VELEX method and associating them with the experimental results to be studied which is more close to the experimental results and the effect of the parameters selected in each method.

After the comparison we found that the coefficient of friction the greatest impact on the performance whenever the lack of friction coefficient the greater the performance and the values of the J.F. Debongnie method higher than the values of the f.VILLE and VELEX method of the effect of the loss factor because it also affects the performance the greater the coefficient of loss whenever the performance.

Downloads

Download data is not yet available.

References

[1] Thaer O, Simulation de l’usure et d’avaries sur des dentures d’engrenages cylindriques - Influence sur le comportement statique et dynamique de transmissions par engrenages, 2012
[2] Bechkri B, ANALYSE DES DÉFAUTS DE DENTURE ET LEURS INFLUENCES SUR LES TRANSMISSIONS MÉCANIQUES PAR ENGRENAGES, 2007
[3] Stewart, R.M. The specification and developpement of a standard gearbox monitoring. 2nd International Conference on Vibration in Rotating Machines, Cambridge, 1980, p. 353-358.
[4] Sidahmed, M., Garnier, C. Détection de défauts dans les engrenages. CETIM information, 1991, n° 124, p. 71-74.
[5] Ghribi D, OPTIMISATION DES CORRECTIONS DE FORME DANS LES ENGRENAGES DROITS ET HELICOIDAUX - APPROCHES DETERMINISTES ET
PROBABILISTES-, 2013
[6] Höhn, B. R., Michaelis, K., Wimmer, A., “Low Loss Gears”. AGMA Fall Technical meeting, Paper No. 05FTM11, 2005.
[7] Maifi T, ANALYSE EXPERIMENTALE DE LA FATIGUE DES
ENGRENAGES A DENTURE DROITE, 2012
[8] Sellami S, ANALYSE DES FACTEURS INFLUANT SUR LA PRECISION CINEMATIQUE DES TRANSMISSION PAR ENGRENAGES, 2010
[9] Diab Y, Analyse des pertes de puissance dans les transmissions par engrenages à grande vitesse. Applications aux réducteurs industriels et aux machines textiles, 2005
[10] Johan PASCAL MESURE ET PRÉDICTION DES DISTORSIONS DES ENGRENAGES TRAITÉS PAR INDUCTION, 2012
[11] J.F. Debongnie, CONCEPTION ET CALCUL DES ÉLÉMENTS DE MACHINES VOLUME 3 Version 1, juin 2006 .pp 133-137
[12] Velex P, Ville F. An Analytical Approach to Tooth Friction Losses in Spur and
Helical Gears—Influence of Profile Modifications, 2009, doi: 10.1115/1.3179156

Downloads

Published

2019-08-28

How to Cite

AROUDJ, M.; INEL, F. INFLUENCE OF COEFFICIENT OF FRICTION ON THE PERFORMANCE OF PARALLEL GEARS. Journal of Fundamental and Applied Sciences, [S. l.], v. 11, n. 3, p. 1135–1150, 2019. DOI: 10.4314/jfas.v11i3.6. Disponível em: https://www.jfas.info/index.php/JFAS/article/view/536. Acesso em: 25 feb. 2024.

Issue

Section

Articles